We use cookies to personalize content, interact with our analytics companies, advertising networks and cooperatives, and demographic companies, provide social media features, and to analyze our traffic. Our social media, advertising and analytics partners may combine it with other information that you’ve provided to them or that they’ve collected from your use of their services. Learn more.
This simple bottle opener can be milled entirely on the Shapeoko. The deep luster of the wood and shiny finish of the aluminum balance each other nicely for a finished object that works well and looks good.
Note that the materials for this project allow you to make 10-15 of these bottle openers.
to Share — to copy, distribute and transmit the work
to Remix — to adapt the work
to make commercial use of the work
Under the following conditions:
Attribution — You must attribute the work in the manner specified by the author or licensor (but not in any way that suggests that they endorse you or your use of the work).
With the understanding that:
Waiver — Any of the above conditions can be waived if you get permission from the copyright holder.
Public Domain — Where the work or any of its elements is in the public domain under applicable law, that status is in no way affected by the license.
Other Rights — In no way are any of the following rights affected by the license:
** Your fair dealing or fair use rights, or other applicable copyright exceptions and limitations;
** The author's moral rights;
** Rights other persons may have either in the work itself or in how the work is used, such as publicity or privacy rights.
Comments
I noticed in step 6 that the aluminum through holes are not very "circular". Is this from the MakerCam G-code or is this an issue with the precision of the machine?
Greetings- the holes are a little eccentric because I was running the feedrate too high on those and it was dragging the bit off-axis. If I were to run the job again I'd take those to half the speed for a tight perfect circle.
How thick the cut in aluminium could actually be? Have you tried with deeper cuts maybe? would be 1inch cut in aluminium too much to handle for shapeoko?
I know it's a 600$ cnc and I don't expect it to run as a 15k one, but I am wondering where are the limits.
I'm an industrial designer and my main use for shapeoko would be 1off pieces for prototyping.
Opening the Easel file, the simulation looks really thin at the sides of the aluminum opening compared to the photos. Like it would be fragile when opening a bottle... Should this really be cut using 1/8" bit with the "On Path" setting? Is the 1/32" upcut bit intended for the design on the walnut?
Comments
I noticed in step 6 that the aluminum through holes are not very "circular". Is this from the MakerCam G-code or is this an issue with the precision of the machine?
Marc Schaefermeyer · November 14, 2013
Greetings- the holes are a little eccentric because I was running the feedrate too high on those and it was dragging the bit off-axis. If I were to run the job again I'd take those to half the speed for a tight perfect circle.
Michael Una · November 22, 2013
How thick the cut in aluminium could actually be? Have you tried with deeper cuts maybe? would be 1inch cut in aluminium too much to handle for shapeoko?
Matej Stefanac · December 11, 2013
I know it's a 600$ cnc and I don't expect it to run as a 15k one, but I am wondering where are the limits. I'm an industrial designer and my main use for shapeoko would be 1off pieces for prototyping.
Matej Stefanac · December 11, 2013
Using this technique, you could cut through 1" aluminum for sure. You just have to go slow and not step down too much per pass.
Michael Una · March 05, 2014
What are the dimensions?
Julian Stanton · December 12, 2014
The instructions for this project have disappeared. Are they still available?
John Shatney · July 16, 2015
Using basic Easel settings for aluminum it says it will take 9 hours to cut out. So.... that can't be right?
Theo Retos · June 23, 2016
Opening the Easel file, the simulation looks really thin at the sides of the aluminum opening compared to the photos. Like it would be fragile when opening a bottle... Should this really be cut using 1/8" bit with the "On Path" setting? Is the 1/32" upcut bit intended for the design on the walnut?
Fred Housel · September 05, 2018