Switch Game Case
Instructions
Cut walnut to size
Cut the 6'' x 12'' piece of walnut to 4.25'' x 10.75''. This can be done using a table saw, circular saw or even a hand saw if need be.
Estimated time: 1 minutes
Work holding
I used double stick tape to hold the work piece. This is important to have access to the profile of your part; otherwise, you will not be able to finish this project. Be sure to use some sacrificial material under the part. One could also build a jig out of some sacrificial material such as MDF, which is why I added it to Bill of Materials.
Estimated time: 3 minutes
Setting home position,
This is the most important part of this project. It is very important that the center of the end mill is at the center of the bottom left hand corner. Proper alignment is critical for success. This can be ensured by first aligning the X axis. This is done by moving the end mill slightly until it touches the side of the material, and then the Z axis is raised up above the part, and then the X axis is moved to the right by half of the tool diameter. Repeat this step for the Y axis. After this is done, lower the Z axis until the end mill is on the surface of the material.
Estimated time: 5 minutes
Carve
This is the actual carve process that the project takes. The main one that carves out the box, which takes 56 minutes using recommended settings for 1/4'' end mill and an engraving that goes on top of the lid that takes 4 minutes using recommended settings for 1/16'' end mill .
Estimated time: 60 minutes
Finish Work
The box will require some sanding because the tolerances are tight; however, this is done on purpose because of slight variances in accuracy from machine to machine. The exterior and interior sides will need to be sanded to allow proper fitment. Sand until it is a tight fit, but the lid should not be very difficult to remove. finally apply finish and allow to cure.
Comments
Can you share this publicly so we can make it? Thanks!
Audrey Van de Castle · July 17, 2018
OK should be fixed now.
joe mchug · July 18, 2018
It still says it is not shared publicly.
Chris Feeley · July 22, 2018
OK definitely fixed this time I did not realize both the project and file need to be public. First time I have posted a project here.
joe mchug · July 25, 2018
It unfortunately still says "This project has not been shared publicly". Would you mind taking one more shot at sharing it?
Chad Forrester · September 08, 2018
it still says project has not been shared publicly yet.. can u please share it again? thanks
Connor Fatzinger · September 09, 2018
Hello! Can you share the G Code for this?
Eli hughes · September 10, 2018
Please share, this would be great for Christmas
Chris Wineland · October 12, 2018
Please make this public
Chris Wineland · October 23, 2018
file still shows not public. Can you fix?
Edward Colee · December 06, 2018
I would really love to make this but it says it is not public, can you please fix?
Victoria Michels · January 02, 2019
Hello. This is a great design. Would you mind sharing it so that I could grab the code? Thanks!
Cyber Ogre · February 15, 2019
Hi I like this design i am wanting to know if you can share it i would like it to be my first project.
Eddie Young · November 09, 2019
Would be great full to see the easel project .. thank you!
Mohammed Adenwala · December 08, 2019
Can you please share the file
Christopher taylor · April 11, 2020
I'd like to try making this for a present. How do I get access?
Margaret Wesley · November 30, 2020
I can't tell the dates on these comments but the project still says it's not private. Can you share the files with us?
Adam St. LouisPro · December 10, 2020
This would be awesome for me. please share!
Ahron O. · February 04, 2021
Still not public 3/21/21
Mark SchluebPro · March 21, 2021
As of May 5th, still not sharing
Cathy McAndrew · May 05, 2021
can you give us the exact measurements to make this because these are wrong and my grandson would really like one.
Stacy HawkinsPro · August 10, 2024